Soffit and Fascia Replacement Cost in Alberta (2026 Guide)

Soffit is the finished underside of the roof overhang, the panel you see when you stand at the wall and look up. Fascia is the vertical board at the very edge of the roof, running along the eaves and up the gables, which the eavestroughs are screwed to. Together they close off the roof edge so that weather, birds and insects stay out of the attic.

Soffit has a second job that most homeowners never think about: it is the air intake for the attic. Vented soffit panels let outside air in at the eaves, that air rises through the attic and exits at the ridge or roof vents, and that flow keeps the attic cool in summer and cold in winter. Block the soffits with paint, insulation or rot and the attic overheats, shingles age from below and ice dams form at the eaves. Our guide to attic ventilation and roof vents in Alberta explains the numbers.

Fascia carries the eavestrough. Every kilogram of water, ice and debris in the trough hangs off the fascia board, and if that board is soft the hangers pull out, the trough sags, and water pours over the edge onto the foundation. Fascia is also the first thing wind-driven rain hits at the roof edge, and the last line of defence for the ends of the rafters behind it.

Aluminum soffit and fascia is the standard in Alberta and it earns its place. It does not rot, it takes hail reasonably well, it comes pre-finished in a wide range of colours, and vented and solid panels are interchangeable. Vinyl is cheaper but gets brittle in Alberta cold, cracks when hail hits it at minus 20, and fades in prairie UV. Wood looks right on older homes but needs paint every few years. Fibre cement is durable and paintable but heavy and expensive to install.

For most Airdrie homes the honest recommendation is aluminum soffit and fascia over a sound wood sub-fascia. If the existing wood fascia board is rotten, it needs replacing before new aluminum goes over it, which is where the "fascia board replacement cost" line in the table above comes in. Cladding over rot just hides it for a few years.

Two houses with the same number of linear feet can get very different quotes. The following factors are what move the price.

• Eave height: a bungalow is done from ladders and a walk-board; a two-storey or a home on a sloped lot in Cooper's Crossing or Hillcrest may need scaffolding or a lift.
• Soffit depth: a 12 inch overhang uses far less material and labour than a 24 or 36 inch one, and the cost per linear foot rises with depth.
• Corners, gables and returns: every corner and gable end adds cutting, trim and time. A simple rectangle is cheap; a house with six gables and two bay windows is not.
• Rotten sub-fascia and rafter tails: wood repair behind the cladding is priced per foot and is often only discovered once the old fascia comes off.
• Eavestrough removal and reinstallation: existing troughs must come down to replace fascia, and old ones often do not survive the trip.
• Ventilation upgrades: converting solid soffit to vented, or adding intake vents, adds a little material and a lot of value.
• Colour and finish: standard white and brown are cheapest; custom colours and woodgrain finishes cost more.
• Bundling: done during a reroof or eavestrough job, the cost per linear foot drops because the crew and access are already there.

Ask any quote to separate soffit, fascia, sub-fascia repair and eavestrough as line items. That lets you compare quotes fairly and see where the money is going.

Soffit and fascia fail slowly and quietly, and most homeowners notice only when the eavestrough falls off or a wasp nest appears. Walk the outside of the house each spring and look for these.

• Peeling or blistering paint on wood fascia, which means moisture is getting into the board.
• Soft, dark or crumbling wood at the corners, at downspout locations and at the ends of the fascia board where the trough overflows.
• Birds, squirrels or wasps getting into the eaves, usually through a gap where a soffit panel has dropped or rotted.
• Sagging or detached eavestroughs, a sign that the fascia can no longer hold the hangers.
• Gaps between the soffit and the wall or panels hanging loose after a Chinook.
• Stuffy, hot attic in summer and frost inside in winter, which often traces back to blocked or non-vented soffit.
• Ice dams every winter with no obvious insulation problem, because the intake air is blocked.
• Water stains on the underside of the soffit, usually from a roof edge leak or an overflowing trough.

Two or three of these together usually mean replacement rather than repair. One localised problem, such as a single rotten corner or a dropped panel, is often a soffit and fascia repair of a few hundred dollars, and it is worth doing before it spreads to the rafter tails.

Repair makes sense when the damage is limited to one or two spots and the rest of the run is sound. Replacing a rotten 3 metre section of fascia and re-hanging the trough, or refitting a few dropped soffit panels, typically runs a few hundred dollars and keeps the rest of the system going for years.

Replacement is the better spend when the wood fascia is painted timber past about 25 years, when the soffit is unvented and the attic needs intake, when rot shows up in more than a couple of places, or when the eavestroughs are also due. Piecemeal repairs on a failing system add up, and each one involves a service call and a ladder set-up.

A middle path is to replace the fascia and clad it in aluminum while leaving sound aluminum soffit alone, or the reverse. A good contractor will tell you which parts are worth keeping. Ask for the quote to be broken down so you can see the difference between the full job and the partial one.

Airdrie sits in Alberta's Hailstorm Alley, and aluminum soffit and fascia take the same hail that dents the roof vents and eavestroughs. Dented fascia, cracked vinyl soffit, and panels torn loose by the wind that comes with a summer storm are all legitimate items on a hail claim. They are also easy to miss, because adjusters and homeowners are focused on the roof.

When a storm like the one on the evening of Aug 8, 2026, which brought quarter-sized hail and damaging wind down the Crossfield–Airdrie corridor, hits your area, walk the perimeter and photograph the fascia, soffit and eavestroughs along with the roof. Note which sides of the house face the storm. Many insurers require hail claims to be filed within 12 months, and Alberta homeowners choose their own contractor for the work. Confirm the specifics with your insurer or broker.

Whether it is worth claiming depends on your deductible and the scale of the damage. Dented fascia alone on one elevation may not clear the deductible, but combined with roof, eavestrough and siding damage from the same storm it usually does. Our roof insurance claim support includes documenting the roof edge and the soffit and fascia so the whole picture goes to the adjuster, and our siding repair service covers the walls below.

Usually yes, if either is due within a few years. The crew is already set up with ladders or scaffolding, the eavestroughs are coming down anyway to replace the fascia, and the roof edge is exposed so drip edge, starter strip and fascia can all be fitted together. Doing the three jobs separately means paying for access three times.

During a reroof, the roof edge is opened up, which is the ideal time to find rotten sub-fascia and rafter tails and to convert solid soffit to vented. Our roof replacement service in Airdrie quotes soffit and fascia as a separate line so you can see exactly what adding it costs, and our Airdrie roof replacement cost guide sets out what the roof itself runs in 2026.

During an eavestrough replacement, the fascia is exposed as soon as the old troughs are off, and a rotten board is the main reason a new trough sags within a couple of years. Our eavestrough service in Airdrie checks the fascia as standard and prices any repair before the new trough goes up, rather than hanging new metal on soft wood.

Soffit and fascia is one of the more approachable exterior jobs for a capable DIYer on a bungalow, and the material cost for aluminum is a fraction of the installed price, roughly $3 to $6 per linear foot for soffit panels and $2 to $5 for fascia cover. The catch is everything else: removing and re-hanging the eavestroughs, cutting and fitting J-channel and F-channel, mitring corners so they do not leak, fastening so the panels do not oil-can or rattle in a Chinook, and working at height for long stretches.

On a two-storey home the height alone pushes it to a professional job. Add rotten wood behind the cladding, which means carpentry before the aluminum goes on, and the time and risk saved by hiring a crew usually outweighs the labour saved. A crew with a brake on site can also form custom fascia profiles and trim that a homeowner cannot buy off the shelf.

If you do tackle it yourself, use vented panels for at least a third of the soffit run, check that attic insulation is not blocking the intake behind them, and never screw eavestrough hangers into fascia cover alone; they need to reach solid wood behind it.

Every home's roof edge is a little different, and the only way to know what soffit and fascia replacement will cost on yours is to measure it and look behind the old material. Apex Roofing Airdrie offers a free, no-obligation on-site estimate with an itemised written quote that separates soffit, fascia, sub-fascia repair and eavestrough, so you can decide what to do now and what can wait.

If the roof is also due, we will price the combined job so you can see the saving. If a storm has dented the roof edge, we document it alongside the roof for your insurance claim. And whatever you decide, the work is done by a local Airdrie crew rather than subcontractors, and it comes with a written workmanship guarantee.